李雪红,雷达,李云
LI Xue-hong,LEI Da,LI Yun

• 1:西安交通大学

摘要(Abstract)：

超高压压缩机填料盘结构复杂并承受很高的压力脉动,填料盘润滑油孔附近会产生明显的应力集中,需要自增强处理来得到良好的预应力状态。本文通过建立填料盘三维有限元模型,利用ANSYS双线性随动强化模型模拟自增强处理过程,分析自增强前后润滑油孔对填料盘等效应力分布、等效对称循环载荷、周向应力分布的影响,定量分析对润滑油孔施加自增强的必要性,得到自增强压力推荐范围。
Due to its complex geometry and being subject to high pulsating pressure,the lube oil hole of the packing cup in hyper-compressor needs autofrettage to obtain a favorable prestress state. A three-dimensional finite element model was built,and the bilinear kinematic hardening model was used in ANSYS to simulate autofrettage process for the lube oil hole. The equivalent stress,the equivalent fully reversed stress,and hoop stress of the packing cup,influenced by the existence of the lube oil hole pre-autofrettage and post-autofrettage,were analyzed to illustrate the necessity of the autofrettage on the lube oil hole and to determine the optimal autofrettage pressure.

关键词(KeyWords)： 超高压压缩机;填料盘润滑油孔;自增强;有限元分析
hyper-compressor;lube oil hole of packing cup;autofrettage;finite element analysis

Abstract:

Keywords:

基金项目(Foundation):

作者(Author): 李雪红,雷达,李云
LI Xue-hong,LEI Da,LI Yun

参考文献(References)：

• [1]卢敬田.超高压往复式压缩机填料盘失效原因分析[D].大连:大连理工大学,2009.
• [2]Hanlon P C.Compressor handbook[M].New York:Mc Graw-Hill,2001.
• [3]Giacomelli E,Graziani F,et al.Advanced Design for Packing Cups of Hyper-compressor Cylinders[C].ASME PVP,2003,2003.
• [4]Giacomelli E,Graziani.Advanced Design of Packing and Cylinders for Hyper-Compressor for LDPE Production[C].ASME PVP 2005,2005.
• [5]Campo N,Chiesi F.Improved Design for Hyper-compressor Packing Cups[C].ASME PVP2007,2007.
• [6]Giacomelli E,Battagli P,Campo N,et al.Autofrettaging Procedures on LDPE Hyper-compressor Components[J].ASME,2006.
• [7]邵国华.超高压容器[M].北京:化学工业出版社,2002,68-76.
• [8]胡林星.聚乙烯超高压反应管残余应力特性的试验研究[D].广州:华南理工大学,2011.
• [9]Hojjati M H,Hassani A.Theoretical and Finite-element Modeling of Autofrettage Process in Strain-Hardening Thick-walled Cylinders[J].International Journal of Pressure Vessels and Piping,2007,84(5):310-319.
• [10]Patrick Terriault.Finite Element Modeling of a Progressively Expanding Shape Memory Stent[J].Journal of Biomechanics,2006,39(15):2837-2844.
• [11]郑小涛,王彪,喻九阳,等.热-机械载荷下厚壁圆筒自增强压力优化分析[J].压力容器,2012,29(9):10,28-31.
• [12]钱凌云,刘全坤,韩豫,等.基于双线性强化模型的挤压凹模自增强技术研究[J].机械工程学报,2011,(12):30-35.
• [13]张云,汪志农,张进杰.往复式压缩机进气阀优化设计方法研究[J].流体机械,2014,42(1):22-24.
• [14]余良俭.往复压缩机故障诊断技术发现与发展趋势[J].流体机械,2014,42(1):36-39.
• [15]尹谢平,陆明和,徐淑芳.高压气瓶用34Cr Mo4-H高强度钢的研究[J].压力容器,2014,31(10):5-12.
• [16]张慢来,张琴,缪锐全.压缩机环状进气阀不同步特性的数值分析[J].排灌机械工程学报,2014,32(5):60-66.
• [17]高耀东,宿福存,李震,等.ANSYS Workbench机械工程应用精华30例[M].北京:电子工业出版社,2013:190-203.