梁真毓;黄玉深;杨旭良;
LIANG Zhen-yu;HUANG YU-shen;YANG Xu-liang;Shenzhen Water Group Co.,Ltd.;

• 1:深圳市水务(集团)有限公司

摘要(Abstract)：

自来水厂V型滤池出水蝶阀工作时需频繁调节开度,阀杆与阀体上的阀杆轴套磨损严重后更换阀杆密封件无法解决阀门的外漏问题。由于修复困难、且修复成本相对较高,常规做法是对阀门进行报废处理。本文介绍一种维修成本低、在线修复蝶阀因阀杆、轴套磨损严重导致外漏故障的方法,实际使用证明效果显著,在节水、节材方面意义较大。
When the butterfly valves on the outlet pipe of V-shaped filtering tank works in water plant,it is needed to adjust the opening frequently,and after the valve stem and the valve stem sleeve in the valve body were worn seriously,the replacement of the valve's stem seal will be unable to solve the problem of the exterior leakage of the valve. Due to the difficulty of repair,and the maintenance cost is relatively high,the general practice is to scrap the worn valve. In this paper a low maintenance cost method for online repairing external leakage fault caused by serious abrasion of valve stem and shaft sleeve of butterfly valve is introduced,the actual use effect is proved to be remarkable,it has a great significance in the aspects of water and material conservation.

关键词(KeyWords)： V型砂滤池;三偏心软密封蝶阀;间隙配合
V-shaped sand filter tank;tri-eccentric soft seat butterfly valve;clearance fit

Abstract:

Keywords:

基金项目(Foundation):

作者(Authors): 梁真毓;黄玉深;杨旭良;
LIANG Zhen-yu;HUANG YU-shen;YANG Xu-liang;Shenzhen Water Group Co.,Ltd.;

参考文献(References)：

• [1]袁泉.智能定位器对蝶阀流量特性的校正及在V型滤池的应用[J]中国给水排水,2007,23(22):66-68.
• [2]陆培文.实用阀门设计手册[M].北京:机械工业出版社,2002.
• [3]付平,常德功.密封设计手册[M].北京:化学工业出版社,2009.
• [4]杨岩,杨恒虎,杨长辉,等.一种新型偏心蝶阀的设计与分析[J].流体机械,2017,45(1):48-54.
• [5]张继伟,雷艳,王剑,等.埋地大口径蝶阀基于刚度、密封性能的最大弯曲载荷研究[J].流体机械,2017,45(10):37-41.
• [6]李宁,穆塔里夫·阿赫迈德,吕星刚.螺旋槽机械密封摩擦副界面流固耦合分析[J].流体机械,2016,44(1):29-33.
• [7]谢苏江,朱宗亮.高温抗氧化柔性石墨密封材料的制备和性能研究[J].流体机械,2017,45(2):12-16.
• [8]许恒杰,宋鹏云.三自由度微扰下的静压干气密封动态特性分析[J].排灌机械工程学报,2017,35(1):56-64.
• [9]陈汇龙,刘金凤,任坤腾,等.基于响应面法的上游泵送机械密封优化[J].排灌机械工程学报,2016,34(3):232-237.
• [10]马凯,蔡仁良,励行根,等.反应堆压力容器用C形密封环的变形特性研究[J].压力容器,2016,33(1):14-19.
• [11]纪克鹏,唐辰,吴志荣,等.三插板阀在振动给料精度控制中的应用[J].包装与食品机械,2015,33(6):63-65.
• [12]杜兆年,吴健.三偏心蝶阀的动水力矩计算[J].甘肃工业大学学报,2003,29(4):70-73.