板翅式热管散热器充液率、倾角对冷板温度场的影响Influence of Inclination and Filling ratio on the Temperature Distribution of Plate-fin Heat Pipe Radiator's Cold Substrate
李佳,金苏敏,岳良,金鹰
LI Jia,JIN Su-min,YUE Liang,JIN Ying
摘要(Abstract)：
动车牵引变流器用板翅式热管散热器由于结构的特殊性,在倾斜时充液率、倾角对空腔冷板温度场的分布影响较大,试验难以实现对此的研究。因此,本文通过建立数学模型,采用ICEPAK数值模拟软件,以实际模型的板翅式热管散热器为例,分析了充液率,倾斜角度对散热器有效传热面积比,冷板温度场分布的影响,得到该散热器的最佳充液率范围为0.5~0.6。
The influence of filling ratio and inclination angle on the temperature distribution of the cavity substrate is quiet significant because of the particular structure of plate-fin heat pipe radiator used in CRH locomotive traction converter,meanwhile,experiments cannot complete this research. Therefore,by establishing mathematical model,using numerical simulation software ICEPAK,taking the real plate-fin heat pipe radiator as example,it is analyzed that the influence of filling ratio and inclination on the effective heat transfer area percent and temperature distribution of cavity substrate plate,the optimum filling ratio range is obtained ranging from 0. 5 ~ 0. 6.
关键词(KeyWords)：
板翅式热管散热器;充液率;倾角;有效传热面积比;温度
plate-fin heat pipe radiator;filling ratio;angle of inclination;effective heat transfer area percent;temperature
基金项目(Foundation):
作者(Author):
李佳,金苏敏,岳良,金鹰
LI Jia,JIN Su-min,YUE Liang,JIN Ying
参考文献(References)：
- [1]李春阳,肖宁,杨闵盛.CRH2型高速动车组CI用热管散热器的研制[J].机车电传动,2012,12(6):30-33.
- [2]Jiao B,Qiu L M,Zhang X B,et al.Investigation on the effect of filling ratio on the steady-state heat transfer performance of a vertical two-phase closed thermosyphon[J].Applied Thermal Engineering,2008,28(11):1417-1426.
- [3]Hussam Jouhara,Zaki Ajji.Yahia Koudsi,et al.Experimental investigation of an inclined-condenser wickless heat pipe charged with water an an ethanol-water azeotropic mixture[J].Energy,2013,51:139-147.
- [4]吴治娟.CPU重力热管使用不同天然工质时的传热特性实验研究[D].重庆:重庆大学,2008.
- [5]施玉洁,岳良,金苏敏,等.牵引变流器用板翅式热管散热器性能实验研究[J].制冷学报,2014,35(5):114-118.
- [6]罗爱华,金鹰,岳良,等.牵引变流器热管式空气冷却器散热性能试验研究[J].制冷学报,2013,34(5):90-94.
- [7]庄骏,张红.热管技术及其工程应用[M].北京:化学工业出版社,2000.
- [8]Holman J P.Heat Transfer[M].北京:机械工业出版社,2011,6.
- [9]史美中,王中铮.热交换器原理与设计[M].南京:东南大学出版社,2009.
- [10]朱祖文,蒋云云,何一坚.天津地区双U型地源热泵地埋管换热器性能模拟研究[J].流体机械,2013,41(6):66-72.
- [11]吴金星,栗俊芬,潘彦凯,等.捆扎式三U型埋管换热器开发及性能分析[J].流体机械,2014,42(8):82-86.
- [12]齐洪洋,高磊,张莹莹,等.管壳式换热器强化传热技术概述[J].压力容器,2012,29(7):71-75.
- [13]Li D,Zhang G Q,Pan K,et al.Numerical simulation on heat pipe for high power LED multi-chip module packaging[C].Electronic Packaging Technology&High Density Packaging,2009:393-397.
- [14]汪双凤,胡艳鑫,陈金建.应用于LED灯具散热的平板热管传热特性[J].工程热物理学报,2012,33(8):1371-1374.