流体机械

2026, v.54;No.649(07) 47-54+63

[打印本页] [关闭]
本期目录(Current Issue) | 过刊浏览(Archive) | 高级检索(Advanced Search)

转速与进气口形状对压缩机油气分离性能的影响
Effects of rotational speed and inlet shape on oil-gas separation performance of compressors

陈江艳,杨晨,王宏辉
Chen Jiangyan,Yang Chen,Wang Honghui

摘要(Abstract):

为揭示旋风分离器两相分离机理,并优化进气结构,提升分离性能,以某压缩机油气分离器为对象,开展仿真与试验研究。基于CATIA构建4种三维模型,并采用CFD-DPM数值方法对不同进气口形状、转速(600~8 000 r/min)及油滴直径(0.5~5μm)工况下的油气分离性能进行系统仿真;结合流场特征分析揭示了转速与进气口形状影响分离性能的内在机理;并选取2种典型进气口结构开展试验,证实数值模型的有效性(中高转速区域偏差小于10%)。结果表明,转速对旋风分离器性能具有主导作用,当转速低至600 r/min时,分离效果极差;油滴直径增大可以显著改善分离性能,1.5μm以上直径油滴在2 000 r/min以上转速时可全部分离;进气口形状对分离性能具备优化作用(矩形>腰形>多圆>单圆),但转速提升至4 000 r/min以上时,因压降显著增加和分离效率增幅放缓而呈现“收益递减”特征;中低速机型优先矩形、腰形进气口,高速机型选用单圆进气口,以平衡分离效率与功耗。研究可为小型旋风分离器优化设计提供参考。
To reveal the two-phase separation mechanism of cyclone separators and optimize the inlet geometry for improved separation performance,numerical simulations and experimental tests were performed on an oil-gas separator for a compressor.Four three-dimensional models were constructed in CATIA.The CFD-DPM numerical approach was employed to systematically investigate the oil-gas separation performance under different working conditions,including varied inlet shapes,rotational speeds of 600~8 000 r/min,and oil-droplet diameters of 0.5~5 μm.The underlying mechanisms through which rotational speed and inlet shape govern separation performance were elucidated via flow-field analysis.Experiments were carried out for two representative inlet configurations to validate the numerical model,yielding prediction deviations below 10% within the medium-and high-speed ranges.The results show that rotational speed exerts a dominant influence on cyclone-separator performance.Extremely low separation efficiency occurs at a rotational speed as low as 600 r/min.Increasing oil-droplet diameter significantly enhances separation performance;droplets larger than 1.5 μm can be fully captured at rotational speeds above 2 000 r/min.Inlet-shape modification provides an effective route for performance optimization,with the efficiency ranking:rectangular>waist-shaped>multi-circular>single-circular.Nevertheless,a diminishing-returns behaviour appears once the rotational speed exceeds 4 000 r/min,caused by a substantial rise in pressure drop together with a decelerating growth rate of separation efficiency.For practical design,rectangular or waist-shaped inlets are recommended for medium-and low-speed units,whereas single-circular inlets are suitable for high-speed compressors to balance separation efficiency and power consumption.This work offers guidance for the optimal design of small-scale cyclone separators.

关键词(KeyWords): 电动汽车;压缩机;旋风分离器;压降;优化设计
electric vehicle;compressor;cyclone separator;pressure drop;optimization design

Abstract:

Keywords:

基金项目(Foundation): 浙江省“尖兵”“领雁”研发攻关计划(2023C01132)

作者(Author): 陈江艳,杨晨,王宏辉
Chen Jiangyan,Yang Chen,Wang Honghui

参考文献(References):

扩展功能
本文信息
服务与反馈
本文关键词相关文章
本文作者相关文章
中国知网
分享