冯瑞鹏;马润梅;宋仁龙;李双喜;张志慧;
Feng Ruipeng;Ma Runmei;Song Renlong;Li Shuangxi;Zhang Zhihui;Research Center for Fluid Sealing Technology,Beijing University of Chemical Technology;Institute of Process Engineering,Chinese Academy of Sciences;

• 1:北京化工大学流体密封技术研究中心
• 2:中国科学院过程工程研究所

摘要(Abstract)：

动压密封端面间液膜发生汽化相变,直接改变了端面间的流体润滑方式,对密封的稳定性产生重要影响。建立了液膜汽化相变数值计算模型,研究了不同工况和结构参数对液膜汽化相变程度和区域的影响,分析了液膜汽化相变后密封性能的变化规律。结果表明:工况和结构参数对液膜的汽化相变有着不同程度的影响,随着转速、压力和槽深的增加,液膜的汽化相变被抑制。当转速高于3×10⁴ r/min、压力高于0.6 MPa、螺旋角大于20°、槽深大于7 μm时,液膜会发生逆汽化现象。液膜的汽化相变对密封性能产生直接的影响。合理选择密封结构参数,可有效利用和控制相变,提高密封性能。
The vaporization phase change of the liquid film between the dynamic pressure seal end faces directly changes the fluid lubrication mode between the end faces,which has an important influence on the stability of the seal.The numerical calculation model of liquid film phase change was established,the area and effects of different working conditions and structural parameters on the vaporization phase change and the area of the vaporization phase change were studied,and the changes of dynamic pressure sealing performance after liquid vaporization phase change were analyzed.The results show that the working condition parameters and structural parameters have different effects on vaporization phase change of liquid film,which is suppressed as the rotation speed,pressure and groove depth increase.When the rotational speed is higher than 3×104 r/min、压力高于0.6 MPa、螺旋角大于20°、槽深大于7 μm时,液膜会发生逆汽化现象。液膜的汽化相变对密封性能产生直接的影响。合理选择密封结构参数,可有效利用和控制相变,提高密封性能。
The vaporization phase change of the liquid film between the dynamic pressure seal end faces directly changes the fluid lubrication mode between the end faces,which has an important influence on the stability of the seal.The numerical calculation model of liquid film phase change was established,the area and effects of different working conditions and structural parameters on the vaporization phase change and the area of the vaporization phase change were studied,and the changes of dynamic pressure sealing performance after liquid vaporization phase change were analyzed.The results show that the working condition parameters and structural parameters have different effects on vaporization phase change of liquid film,which is suppressed as the rotation speed,pressure and groove depth increase.When the rotational speed is higher than 3×10⁴ r/min,the pressure is higher than0.6 MPa,the helix angle is greater than 20°,and the groove depth is greater than 7 μm,the liquid film will undergo reverse vaporization.The vaporization phase change of the liquid film has a direct effect on the sealing performance.Reasonable selection of sealing structure parameters can effectively utilize and control phase change phenomena and improve sealing performance.

关键词(KeyWords)： 汽化相变;螺旋槽;动压密封;相态分布;逆汽化
vaporization phase change;spiral groove;dynamic pressure sealing;phase distribution;inverse vaporization

Abstract:

Keywords:

基金项目(Foundation): 国家重点研发计划项目(2018YFB2000800)

作者(Authors): 冯瑞鹏;马润梅;宋仁龙;李双喜;张志慧;
Feng Ruipeng;Ma Runmei;Song Renlong;Li Shuangxi;Zhang Zhihui;Research Center for Fluid Sealing Technology,Beijing University of Chemical Technology;Institute of Process Engineering,Chinese Academy of Sciences;

参考文献(References)：

• [1]Hughes W F,Winowich N S,Birchak M J,et al.Phase change in liquid face seals[J].Journal of Lubrication Technology,1978,100(1):74-79.
• [2]Beatty P A,Hughes W F.Turbulent two-phase flow in annular seals[J].A S L E Transactions,1987,30(1):11-18.
• [3]Beatty P A,Hughes W F.Stratified two-phase flow in annular seals[J].Journal of Tribology,1990,112(2):372.
• [4]Salant R,Homiller S.Stiffness and leakage in spiral groove upstream pumping mechanical seals[J].A S L E Transactions,1993,36(1):55-60.
• [5]刘录.变工况下汽液两相机械密封端面膜压的计算与试验研究[J].水泵技术,1996(4):42-45.
• [6]宋立群,刘录.抗变机械密封实验研究及在100YⅡ—120泵上的应用[J].石油化工设备技术,1999(3):30-32.
• [7]刘录,沈齐英,邵予工.变工况条件下汽液两相机械密封端面稳定性探讨[J].润滑与密封,2002(3):15-18.
• [8]刘录,沈齐英,邵予工.变工况时气液两相机械密封端面动压实验分析[J].石油机械,2002,30(8):11-13.
• [9]王涛,黄伟峰,王玉明.机械密封液膜汽化问题研究现状与进展[J].化工学报,2012,63(11):3375-3382.
• [10]陈汇龙,王强,李雯瑜,等.基于Fluent的螺旋槽上游泵送机械密封三维微间隙流场数值模拟[J].润滑与密封,2012,37(2):16-19.
• [11]陈汇龙,吴强波,左木子,等.机械密封端面液膜空化的研究进展[J].排灌机械工程学报,2015,33(2):138-144.
• [12]曹恒超,郝木明,李振涛,等.基于相变效应的内压型螺旋槽液膜密封性能分析[J].化工学报,2017,68(9):3532-3540.
• [13]李欢,李双喜,李小芬,等.油气两相动压密封端面结构多参数正交优化及试验研究[J].北京化工大学学报(自然科学版),2017,44(1):76-84.
• [14]孙宪栋,姜绪强,李双喜.机械密封层端面开裂有限元分析[J].流体机械,2018,46(10):29-34.
• [15]王永乐,刘杰,李凤成,等.基于COMSOL的高温双端面机械密封热力耦合分析[J].流体机械,2019,47(3):26-30.
• [16]邓强国,宋鹏云,毛文元,等.气体黏度与温度和压力关系的拟合表达式[J].排灌机械工程学报,2017,35(2):144-151.
• [17]付朝波,宋鹏云.非接触机械密封端面间流体膜流动状态临界雷诺数的讨论[J].润滑与密封,2019,44(7):63-68.