宋飞,陈佳,彭利坤,刘杰
SONG Fei,CHEN Jia,PENG Likun,LIU Jie

• 1:海军工程大学动力工程学院

摘要(Abstract)：

为研究液压滑阀内泄漏规律,搭建了滑阀内泄漏模拟实验台,对10,16,20 mm 3种阀芯直径的滑阀正常间隙(5μm)和过大间隙(40μm)下的泄漏规律进行了试验研究。结果表明,无论在正常间隙还是过大间隙下,滑阀内泄漏都是层流,并得到了径向间隙、密封长度、压差、阀芯直径等因素对泄漏量的影响规律。此外,发现由层流公式得出的理论泄漏量与实测泄漏量总会存在一定的偏差,分析得出偏差可能是由于油液温度、阀芯偏心、倾斜和流态的变化引起的。研究结果可为滑阀内泄漏量的预测、阀的设计和使用提供有益的指导和借鉴。
In order to study the internal leakage rules of hydraulic slide valves,an internal leakage simulation experimental platform of hydraulic slide valves was built to study the leakage of three spool diameters(10,16,20 mm) at normal clearance(5 μm) and excessive clearance(40 μm).The results show that the internal leakage of the valves is laminar flow at both normal clearance and excessive clearance.The influencing rules of radial clearance,sealing length,pressure difference and spool diameter on the internal leakage were obtained. In addition,it was also discovered that there are some differences between the test leakage rate and the theoretical leakage rate obtained by the laminar formula.The cause for the differences may be the change of oil temperature,flow state,eccentricity and tilt of spools.The research results can provide useful guidance and reference for the internal leakage prediction,design and use of hydraulic slide valves.

关键词(KeyWords)： 液压滑阀;内泄漏;层流;径向间隙;密封长度
hydraulic slide valve;internal leakage;laminar flow;radial clearance;sealing length

Abstract:

Keywords:

基金项目(Foundation): 湖北省自然科学基金项目（2016CFB614）;; 海军工程大学青年基金项目（425517K140）

作者(Author): 宋飞,陈佳,彭利坤,刘杰
SONG Fei,CHEN Jia,PENG Likun,LIU Jie

参考文献(References)：

• [1]王栋梁，殷晨波，贾文华，等.表面粗糙度对滑阀式液压阀缝隙流动特性的影响[J].润滑与密封，2016,41(6):46-48.WANG D L,YIN C B,JIA W H,et al.Effect of surface roughness on gap flow of hydraulic slide valve[J].Lubrication Engineering,2016,41(6):46-48.
• [2]王栋梁，徐海涵，贾文华，等.阀芯与阀腔微观表面对缝隙流动的影响[J].润滑与密封，2015,40(6):32-35.WANG D L,XU H H,JIA W H,et al.Effect of microscopic surface of spool and valve chamber on gap flow[J].Lubrication Engineering,2015,40(6):32-35.
• [3]荣刚.液压滑阀内部结构变形与流量泄漏研究[D].杭州：浙江大学，2015.RONG G.Research on structural deformation and leakage loss in hydraulic spool valve[D].Hangzhou:Zhejiang University,2015.
• [4]陈大为.液压滑阀卡紧、泄漏仿真和试验研究[D].济南：山东大学，2015.CHEN D W.Simulation and experimental investigation of clamping and leakage in hydraulic slide valves[D].Jinan:Shandong University,2015.
• [5]海因茨K.米勒，伯纳德S.纳.流体密封技术——原理与应用[M].北京：机械工业出版社，2002.HEINA K MULLER,BERNARD S NAU.Fluid sealing technology principles and applications[M].Beijing:China Machine Press,2002.
• [6]卢明.间隙密封式伺服液压缸密封特性研究及仿真[D].武汉：武汉科技大学，2010.LU M.Research and simulation on the gap type servo hydraulic cylinder seals[D].Wuhan:Wuhan University of Science and Technology,2010.
• [7]鄢勇.液压缸间隙密封流场仿真分析[D].武汉：武汉科技大学，2011.YAN Y.Simulation and analysis on flow field of hydraulic cylinder gap seal[D].Wuhan:Wuhan University of Science and Technology,2011.
• [8]陈静.液压元件间隙的泄漏量及其控制研究[D].武汉：武汉科技大学，2013.CHEN J.Research and control the leakage of hydraulic component clearance[D].Wuhan:Wuhan University of Science and Technology,2013.
• [9]周梓荣，曾曙林.环形间隙中泄漏流量的影响因素研究[J].润滑与密封，2005(1):7-9.ZHOU Z R,ZENG S L.Research on the influence factors of leakage in annular clearance seals[J].Lubrication Engineering,2005(1):7-9.
• [10]周梓荣.水力驱动的冲击破岩系统及其关键技术研究[D].长沙：中南大学，2010.ZHOU Z R.Research on water-powered rock drill system and its key technology[D].Changsha:Central South University,2010.
• [11]塔鲁达纳夫斯基K.非接触密封[M].北京：机械工业出版社，1986.TRUTNOVSKY KARL.Bruhrungsfreie dichtungen[M].Beijing:China Machine Press,1986.
• [12]杨秀峰.水压环形缝隙泄漏特性的理论和实验研究[D].武汉：华中科技大学，2012.YANG X F.Theoretical and experimental researches on leakage characteristics of water hydraulic annular clearance[D].Wuhan:Huazhong University of Science and Technology,2012.
• [13]陈轶杰，郑冠慧，郭建娟，等.基于紊流状态的阻尼阀缝隙节流解析计算[J].力学与实践，2013,35(2):35-39.CHEN Y J,ZHENG G H,GUO J J,et al.Analysis of aperture throttle of damping valve based on turbulence[J].Mechanics in Engineering,2013,35(2):35-39.
• [14]薛晓虎.液压系统缝隙内流体泄漏特性的分析[J].机械工程学报，2004,40(6):75-80.XUE X H.Analysis on the fluid leakage characteristic in gaps of the hydraulic system[J].Chinese Journal of Mechanical Engineering,2004,40(6):75-80.
• [15]蔡标华，秦子明，石兆存，等.阀口形状对套筒调节阀调控特性的影响[J].流体机械，2019,47(4):49-53.CAI B H,QIN Z M,SHI Z C,et al.Effect of valve throat shape on the regulating performance of the sleeve regulating valve[J].Fluid Machinery,2019,47(4):49-53.
• [16]马浩东，何睿，陈殿京.基于声发射理论的安全阀气体内漏信号特征研究[J].压力容器，2020,37(2):24-29.MA H D,HE R,CHEN D J.Research on signal characteristics of safety valve leakage based on the acoustic emission technology[J].Pressure Vessel Technology,2020,37(2):24-29.
• [17]钱锦远，杨佳明，吴嘉懿，等.阀门流固耦合的研究进展[J].流体机械，2021,49(2):57-65.QIAN J Y,YANG J M,WU J Y,et al.Research progress of fluid-structure interaction of valves[J].Fluid Machinery,2021,49(2):57-65.
• [18]许贤良，朱兵，张军，等.同心环形缝隙流理论研究[J].安徽理工大学学报（自然科学版），2004,24(3):40-42.XU X L,ZHU B,ZHANG J,et al.The research of the concentric ring slit flow[J].Journal of Anhui University of Science and Technology(Natural Science),2004,24(3):40-42.
• [19]范家辉.综合传动液压滑阀流场特性与间隙泄漏研究[D].北京：北京理工大学，2016.FAN J H.Study on flow field and clearance leakage of integrated transmission hydraulic spool valve[D].Beijing:Beijing Institue of Technology,2016.
• [20]薛红军，许晓东，危敏，等.大通径滑阀缝隙流场分析及试验研究[J].船舶工程，2011,33(3):53-57.XUE H J,XU X D,WEI M,et al.Analysis and experimental study on flow field in gap on large diameter slide valve[J].Ship Engineering,2011,33(3):53-57.