PTFE垫片压缩蠕变及其对法兰连接密封性能的影响Compressive creep behavior of PTFE gaskets and its effect on the sealing performance of bolted flange joints
陈维,陶家辉,吴国俊,聂德福
Chen Wei,Tao Jiahui,Wu Guojun,Nie Defu
摘要(Abstract):
针对聚四氟乙烯(PTFE)垫片在压缩载荷下发生蠕变、引发螺栓法兰连接密封失效的工程问题,开展了25~45 MPa初始压缩应力下PTFE垫片室温蠕变试验,以及4 MPa氦气介质泄漏率试验,建立了泄漏率与垫片应力的关系,并结合有限元仿真,分析垫片接触应力及法兰连接密封性能随服役时间的变化。结果表明,PTFE垫片的压缩蠕变具有明显的应力敏感性和时间依赖性,蠕变变形主要集中在加载后的前4 h;螺栓预紧载荷为10,20,30 kN三种工况下前4 h蠕变变形分别占1年总蠕变量的49.2%,50.9%和52.0%;垫片泄漏率随接触应力增大而降低,且在低应力阶段对应力变化更为敏感;垫片蠕变使螺栓预紧力和垫片接触应力随服役时间下降,导致泄漏率增加,其中,密封性能下降主要发生在安装预紧后的前4 h。研究结果可为PTFE垫片螺栓法兰连接结构的再紧固时机确定、长时服役性能评估及失效预防提供理论依据与数据支撑。
Aiming at sealing failure in bolted flange joints caused by the compressive creep of polytetrafluoroethylene(PTFE) gaskets,room-temperature creep tests were conducted at initial compressive stresses of 25~45 MPa.Leakage tests were performed using helium at a pressure of 4 MPa.The relationship between leakage rate and gasket stress was established.Finite element simulations were used to evaluate changes in gasket contact stress and sealing performance over service time.The results indicate that PTFE gasket creep is stress-sensitive and time-dependent.Most creep deformation occurs within the first 4 h after loading.For the three bolt pre-tightening load cases of 10,20 and 30 kN,the creep deformation within the first 4 h constitutes 49.2%,50.9% and 52.0% of the total creep deformation over one-year duration,respectively.Leakage rate decreases with increasing contact stress and is more sensitive to stress changes at lower stress levels.Gasket creep causes bolt preload and gasket contact stress to decline over time,resulting in an increased leakage rate.Most deterioration in sealing performance occurs within the first 4 h after initial tightening.The results provide a basis for determining retightening time assessing long-term sealing performance and preventing sealing failure in PTFE-gasketed bolted flange joints.
关键词(KeyWords):
PTFE垫片;压缩蠕变;泄漏率;法兰连接
PTFE gasket;compressive creep;leakage rate;flange connection
基金项目(Foundation): 国家重点研发计划课题(2024YFB3713605)
作者(Author):
陈维,陶家辉,吴国俊,聂德福
Chen Wei,Tao Jiahui,Wu Guojun,Nie Defu
参考文献(References):
- [1] Chen X D,Cui J,Lu Y R,et al. Structural design,manufacturing and maintenance technology of flange seal for pressure equipment based on leak rate control[C]//Proceedings of the ASME 2015 Pressure Vessels and Piping Conference,2015:PVP2015-45352.
- [2] Wang L,Chen X D,Fan Z C,et al.FEM stress analysis of bolted flange joints in elevated temperature service condition[C]//Proceedings of the ASME 2018 Pressure Vessels and Piping Conference,2018:PVP2018-84444.
- [3] 孔慈宇,陈春辉,张斌,等 . 管法兰用柔性石墨金属齿形垫泄漏率及其预测模型[J]. 压力容器,2019,36(12):12-15.Kong C Y,Chen C H,Zhang B,et al.Leakage rate and prediction model of flexible graphite metal toothed gasket for pipe flanges[J].Pressure Vessel Technology,2019,36(12):12-15.
- [4] 甘兵,罗小平 . 聚四氟乙烯换热器传热特性试验研究[J].压力容器,2016,33(8):7-12.Gan B,Luo X P.Experimental study on heat transfer characteristics of flue gas heat exchanger[J].Pressure Vessel Technology,2016,33(8):7-12.
- [5] Kumar V,Koorata P K. Low stress creep response of PTFE sealants applied to pem fuel cells[J].Journal of Applied Polymer Science,2024,141(17):11.
- [6] Guo J Q,Zheng X T,Zhang Y,et al. A unified continuum damage mechanics model for predicting the stress relaxation behavior of high-temperature bolting[J]. Journal of Pressure Vessel Technology,2014,136(1):011203.
- [7] Guo J Q,Meng W Z,Zheng X T,et al.Prediction of stress relaxation from creep data in terms of average creep rate[J].Journal of Strain Analysis for Engineering Design,2015,50(1):15-24.
- [8] Zheng X T,Wen X,Wang W,et al.Creep-ratcheting behavior of PTFE gaskets under various temperatures[J].Polymer Testing,2017,60:229-235.
- [9] Xue W L,Bai J,Zhang Z Z,et al.Creep mechanical performance of cryogenically aged PTFE at room temperature[J].Cryo,2026,2(2):5.
- [10] 张雨果,谢苏江,胡宏玖.膨体聚四氟乙烯垫片的厚度对力学行为和密封性能的影响[J]. 流体机械,2015,43(10):11-15.Zhang Y G,Xie S J,Hu H J.Effects of thickness of expanded polytetrafluoroethylene gaskets on mechanical and sealing behaviors[J].Fluid Machinery,2015,43(10):11-15.
- [11] Zheng X T,Wen X,Gao J Y,et al. Temperaturedependent ratcheting of PTFE gaskets under cyclic compressive loads with small stress amplitude[J].Polymer Testing,2017,57:296-301.
- [12] EN 13555 Flanges and their joints–Gasket parameters and test procedures relevant to the design rules for gasketed circular flange connections[S].
- [13] 裴景克,李文泽,龚鹏剑,等.温度-应力耦合条件下聚四氟乙烯的压缩蠕变行为与寿命预测[J]. 高分子材料科学与工程,2020,36(8):122-129.Pei J K,Li W Z,Gong P J,et al.Compression creep behavior and life prediction of polytetrafluoroethylene under temperature-stress coupling condition[J].Polymer Materials Science and Engineering,2020,36(8):122-129.
- [14] 王靖惠,李吉康,刘争,等.温度-应力耦合下聚四氟乙烯压缩蠕变行为及本构描述[J]. 机械强度 ,2024,46(4):959-968.Wang J H,Li J K,Liu Z,et al. Creep behavior and constitutive description of polytetrafluoroethylene under temperature-stress coupling[J]. Journal of Mechanical Strength,2024,46(4):959-968.
- [15] 陶家辉,王璐,马书豪.聚四氟乙烯垫片压缩蠕变特性及本构模型研究[J]. 化工设备与管道 ,2026,63(1):71-75.Tao J H,Wang L,Ma S H.Compression creep behaviors and constitutive models of polytetrafluoroethylene gaskets[J].Process Equipment&Piping,2026,63(1):71-75.
- [16] 顾伯勤,陈晔 . 高温螺栓法兰连接的紧密性评价方法[J].润滑与密封,2006,31(6):39-41.Gu B Q,Chen Y. Tightness assessment method of bolted flanged connections at elevated temperature[J].Lubrication Engineering,2006,31(6):39-41.
- [17] 张增禧,王曙,顾伯勤,等 . 垫片密封泄漏模型研究[J].压力容器,2001,18(2):4-6.Zhang Z X,Wang S,Gu B Q,et al. Investigation of leakage models of gasket seal[J]. Pressure Vessel Technology,2001,18(2):4-6.