流体机械

2026, v.54;No.649(07) 110-118

[打印本页] [关闭]
本期目录(Current Issue) | 过刊浏览(Archive) | 高级检索(Advanced Search)

基于多气阀独立工作的压缩机气阀故障机理与特征提取
Fault mechanism and feature extraction of compressor valves based on independent operation of multiple valves

李迎丽,杨传明,张辰,张进杰,王瑶
Li Yingli,Yang Chuanming,Zhang Chen,Zhang Jinjie,Wang Yao

摘要(Abstract):

针对顶开吸气阀无级气量调节工况下往复压缩机气阀故障特征易受调节系统影响、故障诊断难度显著增大的问题,基于该工况下不同吸气阀存在独立工作行为的特点,构建了一种多气阀独立工作机理模型。将吸气阀弹簧刚度、卸荷器延迟时间与吸气阀结构参数等关键结构和性能参数设为独立变量,引入弹簧刚度异常、阀片断裂泄漏和卸荷器动作滞后等故障影响,开展了无级气量调节与吸气阀故障耦合的仿真研究。进一步完成了模型试验验证,提取了动态压力信号中的故障特征,并分析了不同故障特征的敏感性。结果表明:多气阀独立工作机理模型可满足变负荷与满负荷工况下压缩机工作过程的仿真需求,模型仿真结果与试验数据整体偏差在10%以内。随着吸气阀弹簧刚度从1 000 N/m增至19 000 N/m,缸内最小压力降低26 111 Pa,降幅为31.43%;指示功增大152 J,增幅为34.38%。随着卸荷器延迟时间从0增至20 ms,指示功减小136 J,降幅为28%。随着泄漏率从0%增至40%,最小压力升高7 933 Pa,增幅为10.18%;指示功减小278 J,降幅为57.31%;最大压力降低122 303 Pa,降幅为43.74%;平均压力降低29 894 Pa,降幅为21.93%。研究成果为实际气阀故障诊断提供了理论和数据支撑。
To address the issue that under stepless capacity regulation conditions with top-open suction valves,the fault characteristics of reciprocating compressor valves are easily affected by the regulation system,significantly increasing the difficulty of fault diagnosis,a multi-valve independent working mechanism model was constructed based on the characteristic that different suction valves exhibit independent working behaviors under such conditions.Key structural and performance parameters such as suction valve spring stiffness,unloader delay time,and suction valve structural parameters were set as independent variables.Fault effects including spring stiffness abnormality,valve plate fracture leakage,and unloader action lag were introduced,and a simulation study on the coupling of stepless capacity regulation and suction valve faults was carried out.Model experimental verification was further completed,fault features were extracted from dynamic pressure signals,and the sensitivity of different fault features was analyzed.The results show that the multi-valve independent working mechanism model can meet the simulation requirements of the compressor working process under variable load and full load conditions,with the overall deviation between model simulation results and experimental data within 10%.As the suction valve spring stiffness increases from 1 000 N/m to 19 000 N/m,the minimum pressure in the cylinder decreases by 26 111 Pa,a decrease of 31.43%;the indicated work increases by 152 J,an increase of 34.38%.As the unloader delay time increases from 0 to 20 ms,the indicated work decreases by 136 J,a decrease of 28%.As the leakage rate increases from 0% to 40%,the minimum pressure increases by 7 933 Pa,an increase of 10.18%;the indicated work decreases by 278 J,a decrease of 57.31%;the maximum pressure decreases by 122 303 Pa,a decrease of 43.74%;the average pressure decreases by 29 894 Pa,a decrease of 21.93%.The research results provide theoretical and data support for actual valve fault diagnosis.

关键词(KeyWords): 无级气量调节;吸气阀;独立工作;耦合;信号特征
stepless capacity regulation;suction valve;independent working;coupling;signal characteristics

Abstract:

Keywords:

基金项目(Foundation): 中国石油天然气股份有限公司科学研究与技术开发项目(2021DJ6802)

作者(Author): 李迎丽,杨传明,张辰,张进杰,王瑶
Li Yingli,Yang Chuanming,Zhang Chen,Zhang Jinjie,Wang Yao

参考文献(References):

扩展功能
本文信息
服务与反馈
本文关键词相关文章
本文作者相关文章
中国知网
分享