姜希彤,刘晓红,王君,宋永兴
JIANG Xi-tong,LIU Xiao-hong,WANG Jun,SONG Yong-xing

• 1:中国石油大学(华东)
• 2:济南市政工程设计研究院(集团)有限责任公司

摘要(Abstract)：

将爪式流体机械的曲爪型和直爪型转子在型线构成、工作过程、受力变形进行对比。分析两种转子在工作性能方面的不同,并对转子的流场和受力进行数值模拟。研究结果表明:在相同半径条件下,直爪型转子的相对余隙容积小比曲爪型转子,曲爪型转子的压力比和压缩效率高于直爪型转子。直爪转子的最大应力小于曲爪转子,爪背无应力集中现象,力学性能好,承载能力强。
The straight rotor and curved rotor of claw type fluid machinery were compared in terms of the profile construction,work process and stress. Two kinds of rotor were analyzed in different performance and were numerically simulated in the flow field and force field. The results showed that the relative clearance volume of straight claw rotor was smaller than curved claw rotor under the condition of the same radius. The pressure ratio and the compression efficiency of curved claw rotor were higher than straight claw rotor. The maximum stress of straight claw rotor was lower than curved claw rotor. The straight claw rotor had no stress concentration phenomenon on claw back,and it had good mechanical performance,strong bearing capacity.

关键词(KeyWords)： 直爪型转子;曲爪型转子;压缩效率;受力
straight claw rotor;curved claw rotor;compression efficiency;stress

Abstract:

Keywords:

基金项目(Foundation): 山东省自然科学基金资助项目(ZR2011EEQ020);; 青岛市科技发展计划项目(12-1-4-7-(4)-jch)

作者(Author): 姜希彤,刘晓红,王君,宋永兴
JIANG Xi-tong,LIU Xiao-hong,WANG Jun,SONG Yong-xing

参考文献(References)：

• [1]杨乃恒.真空获得设备[M].北京:冶金工业出版社,1987,76-99.
• [2]刘凯,姜希彤,查海滨,等.爪式流体机械啮合间隙对工作过程的影响[J].流体机械,2013,41(4):56-59,66.
• [3]江茂强,汪学军.大型裙座支撑式球罐有限元应力分析[J].压力容器,2013,30(8):41,58-62.
• [4]余玲,许杰.设备管口载荷计算的准确模拟[J].化工设备与管道,2013,(8):75-79.
• [5]文周,陈婵娟,彭彪.基于Pro/E和Ansys的输送辊有限元分析[J].包装与食品机械,2013,(6):42-44,58.
• [6]姚民生.爪型泵型线的研究[J].真空,1989,(3):25-30.
• [7]徐学忠,谭翰墨,刘建花.特殊爪型真空泵转子型线的研究[J].机床与液压,2013,41(5):81-84.
• [8]王君,刘凯,姜希彤,等.爪式流体机械工作过程特性研究[J].流体机械,2012,40(12):39-43.
• [9]Antonio G.Proposal of a profile geometry suitable for claw rotor compressors[C]:Proceedings of the ASME2012 International Mechanical Engineering Congress&Exposition,November 9-15,2012,Houston,Texas,USA.
• [10]Hsieh C F.A study of the geometric design and gas port of the claw-type rotor[J].Journal of Mechanical Engineering Science,2009,9(223):2063-2069.
• [11]王君,姜希彤,刘凯,等.爪式流体机械工作过程的三维数值模拟[J].工程热物理学报,2012,(2):64-67.
• [12]刘凯.爪式流体机械新型转子型线构建及其工作特性研究[D].青岛:中国石油大学(华东),2013.