何雪明;陈双成;张荣;武美萍;纪小刚;
HE Xue-ming;CHEN Shuang-cheng;ZHANG Rong;WU Mei-ping;JI Xiao-gang;Jiangsu Key Laboratory of Advanced Food Manufacturing Equipment and Technology;Jiangnan University;

• 1:江苏省食品先进制造装备技术重点实验室
• 2:江南大学

摘要(Abstract)：

采用数值分析的方法对柱塞泵各腔内流体的流态进行分析,确定流体的流态,证明了在仿真计算时将流体模型设置为湍流模型的合理性,并在此基础上建立流体分析模型。该模型主要包括吸、排水腔流体模型、配流盘流体模型、润滑液体膜流体模型和柱塞腔流体模型5部分。运用CFD软件对该模型进行分析时,通过动网格技术实现对柱塞泵吸水、加压、排水整个工作过程周期性变化的仿真分析,模拟出柱塞泵工作过程中流场的动力学特性。最后,将仿真得到的柱塞泵排水口压力波动结果与试验结果进行比对,发现仿真结果与试验结果能够较好的吻合,验证了仿真分析的有效性。
Numerical analysis is used for research of the fluid flow regime of each cavity in axial piston pump,and the flow of the fluid is determined. Demonstrated in the simulation of the rationality of fluid model is set as the turbulence model and fluid analysis model is established on this basis. This model includes absorption,drainage cavity fluid model,a port plate fluid model,the lubricating oil film fluid model and a plunger cavity fluid model of the five parts. The CFD software is used to simulate the dynamic characteristics of the flow field in the working process of the piston pump. Dynamic mesh technology is used to realize the working process of the pump,including water absorption,increasing the pressure and drainage. Finally,the axial piston pump drainage simulation of the export pressure pulsation results and the experimental ones are compared,verifying the validity of the simulation results.

关键词(KeyWords)： 轴向柱塞泵;配流特性;CFD;动网格
axial piston pump;flow distribution characteristics;CFD;dynamic mesh technology

Abstract:

Keywords:

基金项目(Foundation): 国家自然科学基金项目(51275210,51105175);; 江苏省产学研项目(BY2013015-30);; 六大人才高峰资助项目(2013-ZBZZ-016)

作者(Authors): 何雪明;陈双成;张荣;武美萍;纪小刚;
HE Xue-ming;CHEN Shuang-cheng;ZHANG Rong;WU Mei-ping;JI Xiao-gang;Jiangsu Key Laboratory of Advanced Food Manufacturing Equipment and Technology;Jiangnan University;

参考文献(References)：

• [1]Ma J,Fang B,Xu B,et al.Optimization of cross angle based on the pumping dynamics model[J].Journal of Zhejiang University(Engineering Science),2010,11(3):181-190.
• [2]Bergada J M,Kumar S,Davies D L,et al.A complete analysis of axial piston pump leakage and output flow ripples[J].Applied Mathematical Modeling,2012,36:1731-1751.
• [3]Bergada J M,Davies D L,Kumar S,et al.The effect of oil pressure and temperature on barrel film thickness and barrel dynamics of an axial piston pump[J].Meccanica,2012,47(3):639-654.
• [4]Bergada J M,Watton J,Haynes J M,et al.The hydrostatic/hydrodynamic behavior of an axial piston pump slipper with multiple lands[J].Meccanica,2010,45:585-602.
• [5]Bergada J M,Haynes J M,Watton J.Leakage and groove pressure of an axial piston pump slipper with multiple lands[J].Tribology Transactions,2008,51:469-482.
• [6]徐兵,李迎兵,张斌,等.轴向柱塞泵滑靴副倾覆现象数值分析[J].机械工程学报,2010,46(20):161-168.
• [7]徐兵,李春光,许书生.基于虚拟样机的轴向柱塞泵球铰-回程盘相对运动关系研究[C].第六届全国流体传动与控制学术会议,2010:188-192.
• [8]张军辉,徐兵,杨华勇.基于虚拟样机的轴向柱塞泵柱塞副性能研究[C].第六届全国流体传动与控制学术会议,2010:217-223.
• [9]马吉恩.轴向柱塞泵流量脉动及配流盘优化设计研究[D].杭州:浙江大学,2009.
• [10]龙飞飞,高果柱,张晓勇,等.柱塞泵螺纹的磁记忆检测技术研究[J].流体机械,2013,41(2):7-11.
• [11]申儒林,卢鹏飞.A11VLO190轴向柱塞泵柱塞副泄漏与润滑特性研究[J].流体机械,2014,42(7):19-24.
• [12]杨智炜,徐兵,张斌.基于虚拟样机技术的轴向柱塞泵特性仿真[C].第四届全国流体传动与控制学术会议,2006:57-62.
• [13]Kumar S,Bergada J M,Watton J.Axial piston pump grooved slipper analysis by CFD simulation of three-dimensional NVS equation in cylindrical coordinates[J].Computers&Fluids,2009,38:648-663.
• [14]Nie S L,Huang G H,Li Y P.Tribological study on hydrostatic slipper bearing with annular orifice damper for water hydraulic axial piston motor[J].Tribology International,2006,39:1342-1354.
• [15]Kumar S,Bergada J M.The effect of piston grooves performance in an axial piston pumps via CFD analysis[J].International Journal of Mechanical Science,2013,66:168-179.
• [16]朱红钧,林元华,谢龙汉.Fluent流体分析及仿真使用教程[M].北京:人民邮电出版社,2010.
• [17]李静.基于CFD的轴向柱塞泵配流特性分析[D].杭州:浙江大学,2008.