胡良波,周邵萍,张浩,丁晓霞
HU Liang-bo,ZHOU Shao-ping,ZHANG Hao,DING Xiao-xia

• 1:华东理工大学承压系统与安全教育部重点实验室
• 2:上海福斯特流体机械有限公司

摘要(Abstract)：

为了研究不同湍流数值模拟方法对多级离心泵性能预测的适用性,分别采用雷诺时均法(标准k-ε)、大涡模拟法(LES)和分离涡模拟法(DES)对具有相同结构参数的MD450-60×4多级离心泵内流场进行三维模拟,得到对应的计算扬程和水力效率。再根据经验公式将预测的水力效率转化为泵的运行效率,通过预测值与实验值的平均误差对比结果发现,标准k-ε、DES和LES湍流模型的扬程平均误差分别为14.91%、3.88%和4.41%,效率平均误差分别为7.82%、3.14%和2.86%。因此DES和LES模型计算的结果均满足多级离心泵数值模拟的精度要求。
In order to study the applicability of the turbulence simulation method for performance prediction of a multistage centrifugal pump,Reynolds Average Navier-Stockes simulation( Standard k-ε),Large Eddy Simulation( LES) and Detached Eddy Simulation( DES) were used to simulate the flow field of the MD450-60 × 4 multistage centrifugal pump,and the predicted hydraulic efficiency was transformed into pump's operation efficiency by using empirical equations. The average head error of Standard k-ε,LES and DES turbulent model is 14. 91%,3. 88% and 4. 41% respectively,and the average efficiency error of Standard k-ε LES and DES turbulent model is 7. 82%,3. 14% and 2. 86% respectively. By comparing the numerical results and experimental ones,the results obtained from DES and LES show acceptable agreement.

关键词(KeyWords)： 多级离心泵;湍流模型;水力效率;平均误差
multistage pumps;turbulence model;hydraulic efficiency;average error

Abstract:

Keywords:

基金项目(Foundation): 国家科技支撑计划项目“矿山用大型主排水泵电机系统节能技术的研究与应用”(2013BAF01B01)

作者(Author): 胡良波,周邵萍,张浩,丁晓霞
HU Liang-bo,ZHOU Shao-ping,ZHANG Hao,DING Xiao-xia

参考文献(References)：

• [1]John S.A fast numerical method for flow analysis and blade design in centrifugal pump impellers[J].Computers&Fluids,2009,38(2):284-289.
• [2]邵杰,张桂英,吴玉林.半开式离心泵内部流场的数值模拟研究[J].热能动力工程,2011,26(3):290-294.
• [3]Jafarzadeh B,Hajari A.The flow simulation of a lowspeciflc-speed high-speed centrifugal pump[J].Applied Mathematical Modelling,2011,35:242-249.
• [4]张韬,张淑佳,毛鹏展,等.定常多相位方法与非定常方法用于离心泵数值模拟的比较研究[J].浙江工业大学学报,2009,37(6):56-61.
• [5]Shojaeefarda M H,Tahania M,Ehghaghib M B,et al.Numerical study of the effects of some geometric characteristics of a centrifugal pump impeller that pumps a viscous fluid[J].Computers&Fluids,2012,60:61-70.
• [6]Coutier Delgosha O,Patella R Fortes,Rebound J L,et al.Experimental and Numerical Studies in a Centrifugal Pump with Two-Dimension Curved Blades in Cavitating Condition[J].Journal of Fluids Engineering,2003,125:970-978.
• [7]黄思,王朋,区国惟,等.多级多出口离心泵的数值模拟及试验验证[J].流体机械,2013,41(1):19-22.
• [8]魏培茹,刘卫伟,见文.多级离心泵内部流动的数值模拟与优化.[J].流体机械,2010,38(9):39-42.
• [9]Yang Cong-Xin,Cheng Xiao-Wei.Numerical simulation of three-dimensional flow in a multistage centrifugal pump based on integral modeling[C].Asia-Pacific Power and Energy Engineering Conference,APPEEC,2009.
• [10]王福军.计算流体动力学分析[M].北京:清华大学出版社,2004.
• [11]陈懋章,刘宝杰.中国压气机基础研究及工程研制的一些进展[J].航空发动机,2007,33(1):1-9.
• [12]顾春伟,陈美兰,李雪松,等.DES模型在压气机叶栅中的应用研究[J].工程热物理学报,2008,29(12):29-32.
• [13]李栋,Igor Men’shov,中村佳朗.翼型失速特性的RANS方法与DES方法数值模拟对比分析[J].西北工业大学学报,2006,24(2):103-106.
• [14]闫国军.叶片式泵风机原理及设计[M].哈尔滨:哈尔滨工业大学出版社,2009.11.
• [15]阿卜杜艾尼,谢彦斌.加氢装置原料泵的故障分析及处理[J].流体机械,2012,40(3):55-58.
• [16]古新,潘国华.基于遗传算法的三叶孔板换热器优化设计[J].压力容器,2013,30(7):1520.
• [17]关醒凡.现代泵技术手册[M].北京:宇航出版社,1995,9.