流体惯性对球面螺旋槽轴承承载性能的影响机理Influence mechanism of fluid inertia on bearing performance of spherical spiral groove bearing
董福正,罗忠,李雷,郝昊天,吴炫睿
Dong Fuzheng,Luo Zhong,Li Lei,Hao Haotian,Wu Xuanrui
摘要(Abstract):
为揭示高转速条件下流体惯性对球面螺旋槽轴承承载性能的影响机理,建立考虑惯性效应的球面坐标系润滑模型;基于广义雷诺方程,引入离心惯性项与绕流惯性项;采用保角坐标变换与有限体积法相结合,对控制方程进行高精度离散;通过ANSYS Fluent三维流体仿真验证数值方法的准确性。结果表明,流体惯性使油膜压力分布由局部槽区向轴承外缘转移,最大压力区域呈环形分布,压力梯度显著增强;在转速为12 000 r/min、偏心率约为0.4时,考虑惯性效应后,轴向承载力较无惯性时提升约22%,表明惯性效应显著提高了轴承在高转速下的承载能力;轴承间隙对承载性能影响显著,小间隙下惯性效应更为明显,承载力随间隙增大而逐渐降低。研究明确了惯性项在高转速工况下的润滑分析中不可忽略,为球面螺旋槽轴承在高转速工况下的结构优化与性能提升提供了理论依据。
To reveal the influence mechanism of fluid inertia on the load-carrying performance of spherical spiral groove bearings under high rotational speed conditions,a lubrication model in spherical coordinates considering inertia effects was established.Based on the generalized Reynolds equation,the centrifugal inertia term and the circumferential inertia term were introduced.A combination of conformal coordinate transformation and the finite volume method was adopted to discretize the governing equations with high precision.The correctness of the numerical method was verified through 3D fluid simulation using ANSYS Fluent.The results show that fluid inertia causes the oil film pressure distribution to transfer from the local groove region to the outer edge of the bearing,with the maximum pressure region exhibiting an annular distribution and the pressure gradient significantly enhanced.At a rotational speed of 12 000 r/min and an eccentricity ratio of approximately 0.4,the axial load-carrying capacity considering inertia effects is about 22% higher than that without inertia,indicating that inertia effects significantly improve the load-carrying capacity of the bearing at high rotational speeds.The bearing clearance has a significant influence on the load-carrying performance.Under small clearance,the inertia effect is more pronounced,and the load-carrying capacity gradually decreases as the clearance increases.The study clarifies that the inertia term cannot be neglected in lubrication analysis under high rotational speed conditions,providing a theoretical basis for the structural optimization and performance improvement of spherical spiral groove bearings under high rotational speed conditions.
关键词(KeyWords):
球面螺旋槽轴承;油润滑;承载特性;流体惯性效应;结构参数
spherical spiral groove bearing;oil lubrication;load-carrying characteristics;fluid inertia effect;structural parameters
基金项目(Foundation): 国家自然科学基金资助项目(12272089);; 辽宁省自然科学基金联合基金资助项目(2023-BSBA-102);; 粒子输运与富集技术全国重点实验室资助项目(WZKF-2024-6);; 中央高校基本科研业务专项资金资助项目(N2403022)
作者(Author):
董福正,罗忠,李雷,郝昊天,吴炫睿
Dong Fuzheng,Luo Zhong,Li Lei,Hao Haotian,Wu Xuanrui
参考文献(References):
- [1]Yu X D,Lin Y L,Wang P,et al.Analysis of lubrication characteristics of dynamic-static pressure hybrid thrust bearing considering key factors under eccentric loads[J].Tribology International,2024,194:109471.
- [2]Xue C,Chen Y,Zhu B,et al.A comparative study of structural parameters for spiral groove bearing in centrifugal rotary blood pump[J].Heliyon,2023,9(3):e14313.
- [3]韩原臻,殷玉枫,王嘉誉.径向螺旋槽空气轴承起飞速度与承载能力试验研究[J].润滑与密封,2024,49(3):160-165.Han Y Z,Yin Y F,Wang J Y.Experimental study on take-off speed and load-bearing capacity of radial spiral groove air bearings[J].Lubrication Engineering,2024,49(3):160-165.
- [4]张鑫,殷玉枫,唐杰.不同雷诺数下螺旋槽径向气体轴承承载特性分析[J].润滑与密封,2024,49(6):91-97.Zhang X,Yin Y F,Tang J.The load capacity properties of spiral groove journal gas bearings under various reynolds values[J].Lubrication Engineering,2024,49(6):91-97.
- [5]李凯凯,殷玉枫,赵岩松,等.考虑惯性力的超高速螺旋槽径向轴承承载性能分析[J].润滑与密封,2026,51(6):94-103.Li K K,Yin Y F,Zhao Y S,et al.Analysis of load-carrying capacity of ultra-high-speed helical groove radial bearings considering inertial forces[J].Lubrication Engineering,2026,51(6):94-103.
- [6]Duan L Y,Xu M M.Study on static performance of gas-lubricated thrust bearing based on multi-microporous stainless steel plate[J].Journal of the Brazilian Society of Mechanical Sciences and Engineering,2021,43(5):250.
- [7]Yang T Y,Xiao K,Xiang G,et al.Effects of rotating microgroove on tribo-dynamic performance of coupled bearings[J].International Journal of Mechanical Sciences,2024,279:109629.
- [8]Agrawal N,Sharma S C.Micro-grooved hybrid spherical thrust bearing with non-newtonian lubricant behaviour[J].International Journal of Mechanical Sciences,2023,240:107940.
- [9]盛誉,周陈龙,路昕,等.球面螺旋槽轴承特性的数值仿真分析[J].原子能科学技术,2020,54(4):725-730.Sheng Y,Zhou C L,Lu X,et al.Numerical simulation analysis of spherical spiral groove bearing characteristic[J].Atomic Energy Science and Technology,2020,54(4):725-730.
- [10]Lin X H,Wang R Q,Zhang S W,et al.Study on dynamic characteristics for high speed water-lubricated spiral groove thrust bearing considering cavitating effect[J].Tribology International,2020,143:106022.
- [11]Zhang S W,Jiang S Y,Lin X H.Static and dynamic characteristics of high-speed water-lubricated spiral-groove thrust bearing considering cavitating and centrifugal effects[J].Tribology International,2020,145:106159.
- [12]Huang X,Lin S Y,Liang J H.Modelling approach of hybrid air herringbone grooved journal bearing considering the angular misalignment and centrifugal expansion[J].Tribology International,2023,189:108928.
- [13]Zhang C B,Ao H R,Cheng Y J,et al.Theoretical and experimental studies on nonlinear dynamic performances of gas journal bearing with three pads-rotor system[J].Nonlinear Dynamics,2025,113(9):9331-9349.
- [14]Jiang S Y,Liu P F,Lin X H.Study on static characteristics of water-lubricated textured spiral groove thrust bearing using laminar cavitating flow lubrication model[J].Journal of Tribology,2022,144(4):041803.
- [15]Zhang S D,Yang D J,Li G G,et al.Carrying capacity of spherical hydrostatic bearings including elastic deformation[J].Lubricants,2024,12(3):97.
- [16]Lin X H,Wang S,Jiang S Y,et al.Dynamic characteristics of high-speed water-lubricated spiral groove thrust bearing based on turbulent cavitating flow lubrication model[J].Chinese Journal of Mechanical Engineering,2022,35(1):91-111.
- [17]郭良斌,王祖温,包钢,等.新型环面节流静压气体球轴承压力分布的有限元计算[J].摩擦学学报,2004,24(6):531-535.Guo L B,Wang Z W,Bao G,et al.Finite element analysis of the pressure distribution of externally pressurized spherical gas bearings with inherent compensation[J].Tribology,2004,24(6):531-535.
- [18]Chen S K,Chou H C,Kang Y.Stability analysis of hydrodynamic bearing with herringbone grooved sleeve[J].Tribology International,2012,55:15-28.
- 球面螺旋槽轴承
- 油润滑
- 承载特性
- 流体惯性效应
- 结构参数
spherical spiral groove bearing - oil lubrication
- load-carrying characteristics
- fluid inertia effect
- structural parameters