侯才生,刘涛
Hou Caisheng,Liu Tao

• 1:兰州理工大学机电工程学院

摘要(Abstract)：

在传统的变截面组合型线研究中,中间部分的型线仅仅是由高次曲线的前四项构造而成,这在很大程度上限制了高次曲线的种类,为此提出了以高次曲线的前五项作为研究对象,通过对高次曲线的系数进行组合编码,得到了5种编码序列的高次曲线。利用所建立的变截面齿厚计算模型,研究了不同系数对变截面涡旋型线齿厚变化规律的影响,与此同时,又引入了吸气腔容积、压缩比和高次曲线的泄漏线长度3个性能指标,对5种编码序列的高次曲线作了性能分析。研究表明:高次曲线的系数越靠前,对涡旋压缩机的齿厚及其性能的影响越大,其中编码序列为C_(0123)的高次曲线有最大的吸气容积和压缩比,同时其泄漏线长度也最长。该研究丰富了现有高次曲线的种类,也为高次曲线的优选提供了一种新的方法和思路。
In the traditional research of variable cross-section combination profile,the profile of the middle part is only composed of the first four items of the high-order curve,which restricts the types of high-order curve to a large extent. For this reason,it was proposed to use the first five items of the high-order curve as the research object to encode the coefficients of high-order curve,and the high-order curves of five coding sequences were obtained. The effect of different coefficients on the change law of tooth thickness of variable cross-section scroll profile was investigated using the tooth thickness calculation model of variable crosssection. At the same time,three performance indexes,namely,suction chamber volume,compression ratio and leakage line length of the high-order curve were introduced,and the performance of high-order curve with five coding sequences was analyzed.The research shows that the higher the coefficient of the high-order curve,the greater the influence on the tooth thickness of scroll compressor and its performance.The high-order curve with coding sequence C_(0123) has the maximum suction volume,maximum compression ratio and the longest leakage line length. This investigation enriches the types of the existing high-order curves and provides a new method and idea for the optimization of high-order curve.

关键词(KeyWords)： 高次曲线;组合编码;齿厚计算模型;编码序列
high-order curve;combinatorial coding;tooth thickness calculation model;coding sequence

Abstract:

Keywords:

基金项目(Foundation): 国家自然科学基金项目(51665035)

作者(Author): 侯才生,刘涛
Hou Caisheng,Liu Tao

参考文献(References)：

• [1]IvlevVI,Misyurin S Y.Calculated and experimental characteristics of a scroll machine operating in the air motor mode[J].Doklady Physics,2017,62(1):42-45.
• [2]Lu Y,Roskilly AP,Jiang L,et al.Analysis of a 1kW organic Rankine cycle using a scroll expander for engine coolant and exhaust heat recovery[J].Frontiers in Energy,2017,11(4):527-534.
• [3]Dong A C,Kwon O K,Oh M D.An experimental study on semiconductor process chiller using the digital scroll compressor[J].Journal of Mechanical Science and Technology,2014,28(8):3345-3352.
• [4]程哲铭,欧阳新萍,雷蓉.涡旋式压缩机涡旋型线的研究综述与前景[J].流体机械,2015,43(1):51-56.
• [5]王立存,梁学栋,刘爱军,等.涡旋压缩机型线参数偏好性优化设计[J].重庆大学学报,2010,33(1):42-46.
• [6]彭斌,朱兵国.涡旋型线对涡旋压缩机性能的影响[J].流体机械,2016,44(6):17-23.
• [7]王国梁.采用双圆弧加直线单元组合型线的涡旋压缩机理论及试验研究[J].机械工程学报,2010,46(10):144-147
• [8]邬再新,杜文武,刘涛,等.渐开线-高次曲线组合型线涡旋压缩机的设计及有限元分析[J].压缩机技术,2011(2):5-9
• [9]Bush J W,Beagle W P,Housmen M E.Maximizing scroll compressor displacement using generalized wrap geometry[C]//Proceeding of the international compressor engineering conference at Purdue,USA,1994:205-210.
• [10]彭斌,孙迎.变截面涡旋压缩机数学模型及试验研究[J].机械工程学报,2015,51(14):185-191.
• [11]刘涛,任冠林,柳会敏,等.组合型线涡旋压缩机的动力学模型[J].科学技术与工程,2007,7(19):5055-5057.
• [12]王君,刘振全.采用圆渐开线修正涡旋压缩机涡齿型线[J].机械工程学报,2006,42(6):221-226.
• [13]彭斌,李要红,赵生显,等.无油涡旋压缩机涡旋盘的应变分析及试验验证[J].流体机械,2018,46(1):1-8.
• [14]李超,杨紫娟,丁凯,等.涡旋压缩腔径向泄漏对内部流场影响的分析[J].流体机械,2016,44(1):14-18.