马希金,刘晓睿,张耘
Ma Xijin,Liu Xiaorui,Zhang Yun

• 1:兰州理工大学能源与动力工程学院

摘要(Abstract)：

针对某一典型的油气混输泵,以设计工况下泵的增压和效率提升为优化目标,设计了不同进口安放角的静叶,基于FLUENT软件,采用RNG k-ε模型、SIMPLEC算法对装配不同静叶的单级油气混输泵模型进行数值模拟,得出静叶区域内的压力分布,并分析出不同含气率下不同进口安放角的静叶叶型和混输泵增压及效率之间的关系。结果表明:随着静叶进口安放角的增大,混输泵的增压能力和气液混合能力呈现出先增大后减小的趋势,叶片背面产生低速脱流区的起始点逐渐向进口方向移动;较小的进口安放角使得动静叶交界处流速和压力的不均匀性增加。研究结果对混输泵静叶设计及优化提供了理论参考依据。
With respect to a typical multiphase pump,the diffusers with different setting angles were designed with boosting capacity and efficiency improvement of the pump under design conditions as the optimization objectives. Based on the simulation software FLUENT,the RNG k-ε model and the SIMPLEC algorithm were used to numerically simulate the model of a singlestage multiphase pump equipped with different diffusers,the pressure distribution in the diffuser region was obtained. Additionally,the relationship between the diffuser profile of the multiphase pump with different inlet angles and boosting and efficiency of the multiphase pump under different gas volume fraction(GVF) was analyzed. The results show that with the increase of the diffuser inlet angle,the boosting capacity and the gas-liquid mixing capacity of the multiphase pump show a trend of increasing first and then decreasing,and the starting point of the low-velocity flow separation zone on the back of the vane gradually moved towards the inlet. Smaller diffuser inlet angle makes the inhomogeneity of velocity and pressure at the junction of the impeller and diffuser increase. The research results provide a theoretical reference for the design and optimization of the diffuser of the multiphase pump.

关键词(KeyWords)： 油气混输泵;静叶;进口安放角;气液混合
multiphase pump;diffuser;inlet angle;gas-liquid mixture

Abstract:

Keywords:

基金项目(Foundation): 甘肃省科技攻关项目(KG954-3-11)

作者(Author): 马希金,刘晓睿,张耘
Ma Xijin,Liu Xiaorui,Zhang Yun

参考文献(References)：

• [1]Suh J W,Kim J H,Choi Y S,et al.A study on numerical optimization and performance verification of multiphase pump for offshore plant[J].Proceedings of the Institution of Mechanical Engineers Part A Journal of Power&Energy,2017,231(5):095765091770226.
• [2]周岭，施卫东，陆伟刚.基于数值模拟的深井离心泵导叶性能分析[J].农业工程学报，2011,27(9):38-42.
• [3]马希金，李新凯，王楠，等.导叶叶片数对气液混输泵性能的影响[J].兰州理工大学学报，2012,38(3):51-55.
• [4]李选玉.螺旋轴流式油气混输泵的研制及实验[D].成都：西南石油大学，2014.
• [5]苗长山.多相泵增压单元的工作理论与设计方法[D].北京：中国石油大学，2007.
• [6]吴志旺，见文，刘卫伟.叶片进口安放角对离心泵性能影响[J].水电能源科学，2012,30(9):133-135.
• [7]张人会，郭荣，杨军虎，等.基于CFD的空间导叶内部流场分析及优化设计[J].排灌机械工程学报，2015,33(9):762-767.
• [8]魏清顺，刘在伦.导流器叶片进口安放角对潜水泵性能的影响[J].中国电机工程学报，2012,32(14):109-115.
• [9]马希金，包春辉.导叶叶片数对轴流式油气混输泵内部非定常流场的影响[J].流体机械，2017,45(5):36-41.
• [10]关醒凡．现代泵技术手册[M].北京：中国宇航出版社，2011．
• [11]杨从新，齐亚楠，黎义斌，等.核主泵叶轮与导叶叶片数匹配规律的数值优化[J].机械工程学报，2015,51(15):53-60.
• [12]吴琦，刘雪林.某项目主泵轴封水管线固定点设计优化[J].压力容器，2018,35(2):29-34.
• [13]马希金，张贞贞，侯祎华.多级油气混输泵轴向间隙变化对其性能的影响[J].流体机械，2015,43(4):28-32.
• [14]张金亚，蔡淑杰，朱宏武，等.三级螺旋轴流式混输泵可压缩流场数值模拟[J].农业机械学报，2014,45(9):89-95.
• [15]余志毅，曹树良，王国玉.叶片式混输泵内气液两相流的数值计算[J].工程热物理学报，2007(1):46-48.
• [16]Kim J H,Lee H C,Kim J H,et al.Improvement of hydrodynamic performance of a multiphase pump using design of experiment techniques[J].Journal of Fluids Engineering,2015,137(8):081301.