郑似玉;滕金芳;羌晓青;
ZHENG Si-yu;TENGJin-fang;QIANG Xiao-qing;Shanghai Jiatong University;

• 1:上海交通大学

摘要(Abstract)：

以单级轴流压气机为研究对象,采用数值计算方法研究了叶片位置度超差对压气机流场性能的影响。计算结果表明,当叶片位置度发生变化时,压气机的等熵效率、总压比等气动参数都不同程度地呈现恶化趋势,并且轴向位置度的影响大于周向位置度;叶片周向及轴向位置度的变化对压气机叶片气动载荷和进口攻角的影响规律各不相同。
Inorder to investigate the influence of the positional variability on the axial compressor performance and flow field,largeamounts of numerical simulation were performed in a single-stage axial compressor. Thenumerical results indicate that when the position of the blade section changes,the aerodynamic performance such as isentropic efficiency and total pressure ratio are always reduced,and the axial position has a greater impact than the circular position. Besides,these two positional variability have different influence on aerodynamic loading and incidence angle of the compressor blade.

关键词(KeyWords)： 轴流压气机;位置度超差;流场性能;数值模拟
axial compressor;positional variability;flow field performance;numerical simulation

Abstract:

Keywords:

基金项目(Foundation): 省部级航空基金重点项目(2015ZB57006)

作者(Author): 郑似玉;滕金芳;羌晓青;
ZHENG Si-yu;TENGJin-fang;QIANG Xiao-qing;Shanghai Jiatong University;

Email:

DOI:

参考文献(References)：

• [1]Lange A,Voigt M,Vogeler K,et al.Impact of manufacturing variability on multistage high-pressure compressor performance[J].Journal of Engineering for Gas Turbines and Power,2012,134(11):112601.
• [2]Wunsch D,Hirsch C,Nigro R,et al.Quantification of combined operational and geometrical uncertainties in turbo-machinery design[C].ASME paper,GT2015-43399,2015.
• [3]Fathi A,Alizadeh M.Effects of blade manufacturing deviations on turbine performance[C].ASME paper,GTINDIA2012-9641,2012.
• [4]Benini E,Biollo R.Aerodynamics of swept and leaned transonic compressor-rotors[J].Applied Energy,2007,84:1012-1027.
• [5]陈浮,赵桂杰,宋彦萍,等.叶片弯掠对压气机端壁流动的影响[J].工程热物理学报,2004,25(2):211-215.
• [6]冯秀莲,金东海,桂幸民.叶片弯掠对压气机静子叶片气动性能影响的三维数值模拟[J].航空动力学报,2009,24(10):2338-2343
• [7]郑覃,卢少鹏,羌晓青,等.动叶局部弯曲对压气机流场和性能的影响[J].流体机械,2015,43(7):27-31.
• [8]王祥峰,周逊,王松涛,等.动叶正弯对压气机性能影响的数值研究[J].汽轮机技术,2009,51(6):401-403.
• [9]林棋,娄晨.基于差压式孔板流量计的缩径管段流场数值研究[J].压力容器,2014,32(2):29-37.
• [10]晏祖根,李明,徐可非,等.高速机器人分拣系流机器视觉技术的研究[J].包装食品机械,2014,32(1):28-31.
• [11]魏兵海,吴克启.高性能弯掠叶片及其对内流影响的研究概况[J].流体机械,2001,29(1):31-34.