邱勇
QIU Yong

• 1:江苏振华泵业制造有限公司

摘要(Abstract)：

为了使潜污泵同时具有高效与无过载特性,针对模型泵100QW110-15-7.5的叶轮进行优化设计,采用正交试验设计法,设计了一组7因素3水平的正交方案。对每个方案进行数值模拟,并对计算得到的数据进行极差分析,获得了各几何参数影响性能的主次顺序。采用加权方法,将扬程、效率、轴功率多项指标转化为单项综合性能指标,利用超传递近似法来确定各目标函数的权重因子的数值,并对综合性能指标进行极差分析,得到了潜污泵的最优参数。在数值模拟基础上,对最优模型样机进行了试验,测试结果表明:模型泵的额定点效率达到81.04%,在运行区间内无马鞍区、无过载现象发生,且高效区较宽,满足设计要求。预测曲线与试验曲线基本吻合,表明数值模拟较为准确,对高效无过载潜污泵的设计具有一定的指导意义。
In order to make submersible sewage pump have the characteristics of high-efficiency and no-overload,optimization design of the100QW110- 15- 7. 5 model pump impeller was done by using the orthogonal design method. Orthogonal scheme of seven factors and three levels was designed. Each scheme was calculated by numerical simulation,and the data analyzed by range analysis. The influence primary and secondary orders of geometric parameters on the characteristics were obtained. The head,efficiency and shaft power indicators were converted into a single comprehensive performance indicator by the weighted method. Additionally,the super transitive approximation method was applied to update optimal weighted coefficients in the objective function.Through the comprehensive performance indicator range analysis,the optimization parameter combination was gotten. The optimal model prototype,based on the simulation,was tested. And the test results show that,the efficiency of the model pump reaches81. 04% at the rated point. In the whole process of pump operation,no saddle area and no overload phenomenon occurs,meeting the design requirements. Predicted curve is basically consistent with the experimental one,indicating the numerical simulation is accurate,that means it has a certain significance for high-efficiency non-overload submersible sewage pump design.

关键词(KeyWords)： 潜污泵;正交试验;无过载;优化设计
submersible sewage pump;orthogonal experiment;non-overload;optimized design

Abstract:

Keywords:

基金项目(Foundation):

作者(Author): 邱勇
QIU Yong

参考文献(References)：

• [1]施卫东,桑一萌,王准,等.高效无堵塞泵的研究开发与发展展望[J].排灌机械,2006,(6):48-52.
• [2]施卫东,蒋婷,曹卫东,等.高扬程无过载潜水排污泵的优化设计与试验[J].农业工程学报,2011,27(5):151-155.
• [3]施卫东,孙新庆,陆伟刚,等.低比转数潜水电泵无过载设计[J].农业机械学报,2010,(7):36-39.
• [4]倪合玉.潜水排污泵的工况分析与双流叶轮的无过载设计[J].通用机械,2005,(6):84-87.
• [5]Nishi Y,Fujiwara R,Fukutomi J.Design method for single-blade centrifugal pump impeller[J].Journal of Fluid Science and Technology,2009,4:786-800.
• [6]丛小青,袁寿其,袁丹青.无过载排污泵正交试验研究[J].农业机械学报,2005,(10):66-69.
• [7]丛小青,袁寿其,袁丹青,等.污水泵的研究现状与进展[J].排灌机械,2005,(6):1-5.
• [8]丛小青,袁寿其,袁丹青,等.无过载双流道排污泵性能预测研究[J].排灌机械,2006,(2):4-6.
• [9]袁寿其.低比速离心泵理论与设计[M].北京:机械工业出版社,1997:58-122.
• [10]关醒凡.现代泵理论与设计[M].北京:中国宇航出版社,2011:286-290.
• [11]周岭,施卫东,陆伟刚,等.井用潜水泵导叶的正交试验与优化设计[J].排灌机械工程学报,2011,29(4):312-315.
• [12]王秀礼,朱荣生,苏保稳,等.无过载旋流泵正交设计数值模拟与试验[J].农业机械学报,2012,43(1):48-51.
• [13]黄健勇,张飞珍,张浩,等.斜式轴流泵装置进水流道的正交优化设计[J].排灌机械工程学报,2013,(9):741-746.
• [14]丛小青.无过载排污泵理论与设计方法的研究[D].镇江:江苏大学,2003.
• [15]袁建平,李淑娟,付跃登.用正交试验研究分流叶片对离心泵性能的影响[J].排灌机械,2009,(5):306-309.
• [16]王秀礼,朱荣生,俞志君,等.高低叶片对旋流泵性能影响的研究[J].中国机械工程,2011,22(17):2030-2033.
• [17]张金亚,朱宏武,李艳,等.基于正交设计方法的混输泵叶轮优化设计[J].中国石油大学学报(自然科学版),2009,(6):105-110.
• [18]张金凤,昌杰云,袁寿其,等.变转速工况下汽车冷却水泵内外特性变化规律[J].流体机械,2014,42(8):10-15.
• [19]李彤,周建佳,袁寿其.基于流场计算的螺旋离心泵叶轮静力学分析[J].流体机械,2013,41(12):31-35.
• [20]古新,潘国华,刘敏珊,等.基于遗传算法的三叶孔板换热器优化设计[J].压力容器,2013,30(7):15-20.
• [21]龙云,朱荣生,付强,等.核主泵小流量工况下不稳定流动数值模拟[J].排灌机械工程学报,2014,32(4):20-25.
• [22]吕志昆,郭延明.食品包馅机械中双极变量叶片泵的设计与计算[J].包装与食品机械,2013,31(2):22-24.
• [23]王凯,刘厚林,袁寿其,等.离心泵多工况水力性能优化设计方法[J].排灌机械工程学报,2012,(1):20-24.