陈建垒,张付英,宋娜娜,段晶莹
CHEN Jian-lei,ZHANG Fu-ying,SONG Na-na,DUAN Jing-ying

• 1:天津科技大学
• 2:天津市轻工与食品工程机械装备集成设计与在线监控重点实验室

摘要(Abstract)：

应用有限元分析软件ABAQUS,建立了唇形油封的有限元模型,分析了唇口接触压力对油封密封性能的影响。基于有限元分析结果,集成数值计算理论方法,研究了油封运行时,轴转速对温升、泵汲率、摩擦扭矩及密封性能的影响及规律。结果表明:优化前和优化后2种结构参数的油封模型,其各密封性能指标均满足密封要求;且在分析的工作参数范围内,优化后油封随转速的增加,温度增加的幅度和摩擦扭矩明显低于优化前油封,而泵汲率比优化前有显著提高,表明优化后油封具有较佳的密封性能。
The finite element model of lip seal was built using the finite element analysis software ABAQUS,and the influence of the lip contact pressure on the sealing performance of oil seals was analyzed. Based on the results of finite element analysis and by integrating the theoretical methods of numerical calculation,the effects and rules of the dynamic rotational speed on temperature rise,pumping rate,friction torque and sealing performance were studied. The results show that,for the oil seal models with two structural parameters before and after optimization,all its performance indexes satisfy the sealing requirements;and in the range of the analyzed working parameters,with the increase of the rotational speed of the optimized oil seal,the amplitude of the temperature increase and the friction torque are significantly lower than those before optimization,and the pumping rate increases significantly than before optimization,which shows that the optimized oil seal has better sealing performance.

关键词(KeyWords)： 旋转轴唇形油封;唇口接触压力;温度分布;泵汲率;摩擦扭矩
rotary shaft lip seal;lip contact pressure;temperature distribution;pumping rate;friction torque

Abstract:

Keywords:

基金项目(Foundation): 天津市自然科学基金重点项目(17JCZDJC38800)

作者(Author): 陈建垒,张付英,宋娜娜,段晶莹
CHEN Jian-lei,ZHANG Fu-ying,SONG Na-na,DUAN Jing-ying

参考文献(References)：

• [1]张建斌,郦华兴,姜敏.提高旋转轴油封性能的方法[J].橡胶工业,2001(48):548-551.
• [2]Yang A S,Wen C Y,Tseng C S.Analysis of flow field around a ribbed helix lip seal[J].Tribology International,2009,42:649-656.
• [3]张付英,王宏浩,姜向敏.基于ABAQUS的油封密封性能研究[J].润滑与密封,2017,42(5):78-82.
• [4]王保森,何红,杨伟民.油封唇口压力大小及分布的有限元分析[J].特种橡胶制品,2007,28(2):39-43.
• [5]张佳佳.唇形油封散热机理研究[D].重庆:重庆大学,2011.
• [6]Shi F,Salant R F.A mixed soft elastohydrodynamic lubrication model with interasperity cavitation and surface shear deformation[J].Tribology International,2000,122(1):308-316.
• [7]郭飞,贾晓红,黄乐,等.旋转轴唇形密封混合润滑理论模型和试验验证[J].机械工程学报,2014,50(3):137-144.
• [8]Kang Y S,Sadeghi F.Numerical analysis of temperature distribution at the lip seal-shaft interface[J].Journal of Tribology,1997(119):273-278.
• [9]赵良举,张佳佳,杜长春,等.唇形油封动态散热仿真研究[J].计算机仿真,2011,28(11):324-327.
• [10]张佳佳,赵良举,杜长春,等.唇形油封结构参数对摩擦面温度的影响[J].合肥工业大学学报(自然科学版),2011,34(10):1470-1473.
• [11]赵良举,苏晓燕,杜长春,等.旋转唇形油封泵汲效应及影响因素分析[J].合肥工业大学学报,2011,34(12):1782-1786.
• [12]吴庄俊,赵良举,杜长春,等.结构参数对径向唇形密封圈密封性能的影响研究[J].合肥工业大学学报,2012,35(11):1451-1455.
• [13]李建国,丁玉梅,杨卫民,等.油封密封性能的有限元分析[J].润滑与密封,2006,31(10):116-119.
• [14]圆山重直,王世学,张信荣.传热学[M].北京:北京大学出版社,2011:23-233.
• [15]梁宏伟.往复运动Y形密封圈温度场的研究[D].包头:内蒙古科技大学,2015.
• [16]Fr?lich n D,Magyar B,Sauer B.A comprehensive model of wear,friction and contact temperature in radial shaft seals[J].Wear,2014(311):71-80.
• [17]Hajjam M,Boneau D.Influence of the roughness model on the thermoelastohydrodynamic performances of lip seals[J].Tribology International,2006,39(3):198-205.
• [18]Salant R F.Soft elastohydrodynamic analysis of rotary lip seals[J].Proceedings of the Institution of Mechan-ical Engineers,Part C:Journal of Mechanical Engineering Science,2010,224(12):2637-2647.
• [19]侯文富,鲁志兵,张绍良,等.操作参数对Cr-Mo钢焦炭塔瞬态温度场及热应力影响数值模拟研究[J].压力容器,2018,35(1):38-44.
• [20]叶增荣.基于MPC简化模型的非对称换热器有限元分析[J].压力容器,2017,34(5):38-45.
• [21]由宏新,刘培启,孔闯,等.车载LNG气瓶尾端支撑结构传热比较[J].压力容器,2017,34(10):20-26.
• [22]王森,李占英,李治国,等.新型板式热交换器导流区数值模拟研究[J].压力容器,2017,34(8):25-34.
• [23]杨洋,李一曼,刘丹,等.化工设备弹性支撑设计[J].化工设备与管道,2016,53(5):39-42.
• [24]张博文,刘震涛,张宇,等.高海拔条件下柴油机缸盖热状态变化规律研究[M].机电工程,2016,33(10):1203-1207.
• [25]黄迷梅著.液压气动密封与泄漏防止[M].北京:机械工业出版社,2003.