离心水泵叶轮子午面双曲轮廓的模拟和试验Simulation and Experiment the Hyperbola Profile in the Impeller Meridional Plane of Engine Water Pump
李丽红;徐向阳;刘艳芳;姬芬竹;
LI Li-hong,XU Xiang-yang,LIU Yan-fang,JI Fen-zhu(Beihang University,Beijing 100084,China)
摘要(Abstract):
离心水泵叶轮子午双曲轮廓的设计方法是按照流体的绕角流动原理,遵从流体运动规律设计叶轮的轴面轮廓。这种方法在理论上给从事叶轮设计工程人员提供了一种简单易行的方法。它不仅避免了传统方法的复杂性,而且还摒弃了经验上的任意性。通过用CAD建模,CFD软件分析,可以明显看出,用子午面双曲轮廓方法建立的叶轮模型,回流、二次流明显减少,同时也通过试验验证了用此叶轮的水泵其扬程和效率也有明显的提高。
The impeller axial figure of water pump was designed by the method of the meridian hyperbola figure,according to the principle of the flow in a sector which follows liquid flow law.This way supplies a simple and available method for the engineers who embark on the impeller design.It can't not only avoid the complication of conventional way but also turn away the randomicity of experiential method.The model was built by CAD and was analyzed by CFD.The result was shown that the reversed flows and the twice flows was evidently reduced.At the same time experiment verified that the head and efficiency of the pump was improved distinctly,which installed such impeller.
关键词(KeyWords):
绕角流动;轴面轮廓;二次流;子午双曲轮廓
the meridian hyperbola figure;the flow in a sector;impeller model;reversed flows
基金项目(Foundation): 山东省优秀中青年科学家科研奖励基金项目(潍科计字[2007]87号文件)
作者(Authors):
李丽红;徐向阳;刘艳芳;姬芬竹;
LI Li-hong,XU Xiang-yang,LIU Yan-fang,JI Fen-zhu(Beihang University,Beijing 100084,China)
参考文献(References):
- [1]金树德,陈次昌.现代水泵设计方法[M].北京:兵器工业出版社,1993.
- [2]李世煌.叶片泵的非设计工况及其优化设计[M].北京:机械工业出版社,2006:1-150.
- [3]周玉娟赵林明.Bezier曲线在离心泵水力设计中的应用[J].华北水利学院学报,2000,12:56-59.
- [4]张兄文,李国君,李军.离心泵叶轮内变流量流动特性的数值模拟[J].北京:农业机械学报,2005,12:62-65.
- [5]温正,石良臣,任毅如.FLUENT流体计算应用教程[M].北京:清华大学出版社,2009.
- [6]刘卫东,王振国,周进.采用二阶迎风格式的PISO算法研究[J].航空动力学报,1998,(1):82-85.
- [7]张鸣远景思睿.高等工程流体力学[M].西安:西安交通大学出版,2006.
- [8]陈庆光,吴玉林,刘树红,等.轴流式水轮机全流道内非定常空化湍流的数值模拟[J].机械工程学报,2006,42(6):211-216.
- [9]黄忠富,姜哲,赵斌娟,等.利用小波分析诊断水泵初始阶段的汽蚀故障[J].排灌机械,2005,(2):10-13.
- [10]David thiepxuan Cao.Design of A Centrifugal Pumpfor Liquid Fuel Pumping Application[D].Michigan:Department of Mechanical Engineering,MichiganState University,2002.
- [11]Gill Brent Brent beamson.Research and Developmenton A Magnetically Levitated Rotor Implantable BloodPump[D].Utah:Department of Electrical Engineer-ing,The University of Utah,2001.
- [12]Miner Steven Mark.Potential FlowAnalysis of ACen-trifugal Pump:Comparison of Finite Element Calcula-tion and Laser Velocimeter Measurement.Virginia:University of Virginia,1988.
- [13]Waite,David Marc.A Three-dimensional PotentialFlowAnalysis of Dynamic Fluid Forces Acting on AWhirling Centrifugal Impeller Bounded by AVolute.Virginia:University of Virginia,1990.
- [14]Dong,Ronald rong.The Effect of Volute Geometry onthe Flow Structure,Pressure Fluctuation and Noise inA Centrifugal Pump.The Johns Hopkins University,1994.
- [15]Shilong Chu.Relationship between Unsteady Flow,Pressure Fluctuations and Noise in A centrifugalPump.The Johns Hopkins University,1995.
- [16]蔡江畔,李春,李沈坚.参数曲线在水泵叶轮设计中的应用[J].上海理工大学学报,2008,30(4):9-12.
- [17]CAI Jiang-pan,LI Chun,LI Shen-jian.Application ofParameterized Curves in Pump Impeller design[J].Journal of University of Shanghai for Science andTechnology,2008,30(4):
- [18]彭先珍,喻亮.水泵叶轮CAD系统中的数据库与流动分析模块[J].中南工业大学学报(自然科学版)2002,33(4):88-91.
- [19]PENG Xian-zhen,YU liang.Date Base in CAD Sys-tem of Pump Impeller and Model Construction of Flowanalysis[J].Journal of Central South University ofTechnology(natural science).2002,33(4):