马峰,赵忖
MA Feng,ZHAO Cun

• 1:西安交通大学

摘要(Abstract)：

基于数值方法,以一台单级离心压缩机为研究对象,对其圆截面外蜗壳的型线进行了改进研究。主要措施有:改进蜗壳横截面积沿圆周角的变化规律,以改善蜗壳入口流场的均匀性,降低蜗壳截面最大通流速度;减小蜗舌处蜗壳的横截面积,从而减少蜗壳内通流气体总量,减小蜗壳总流动损失。数值计算结果表明,改进后蜗壳自身气动性能得到明显提升,蜗壳入口流场得到改善,在设计流量下,蜗壳多变效率提高了8.04%,压缩机级多变效率提高了1.26%。
Based on numerical analysis method,research was carried out on the improvement of the profile of circular crosssection volute of a single-stage centrifugal compressor by using the compressor as the research object.The main measures are as follows:modify the variation rule of cross-section of the volute along the circumferential direction to improve the uniformity of the entrance flow field of the volute and reduce the maximum flow velocity of volute cross-section;reduce the cross-sectional area of the volute near the volute tongue to reduce the total flow gas volume in the volute so as to reduce the total flow loss of the volute. The numerical calculation results show that the aerodynamic performance of the volute itself after improvement was substantially improved and the flow field at the inlet of the volute was improved. At the design flow,the polytropic efficiency of the volute was increased by 8.04%,and the polytropic efficiency of the compressor stage was increased by 1.26%.

关键词(KeyWords)： 离心压缩机;蜗壳;性能改进;数值研究
centrifugal compressor;volute;performance improvement;numerical research

Abstract:

Keywords:

基金项目(Foundation):

作者(Author): 马峰,赵忖
MA Feng,ZHAO Cun

参考文献(References)：

• [1]徐忠.离心式压缩机原理[M].北京:机械工业出版社,1990.
• [2]刘伟,齐维彪,王尚锦,等.离心压缩机圆形截面蜗壳内部三维流场的试验研究[J].流体机械,2006,34(11):1-3.
• [3]刘飞,蔡兆麟.离心压缩机级的数值试验及分析[J].通用机械,2005(3):72-75.
• [4]周莉,张鑫.离心压缩机蜗壳内部流动的研究[J].风机技术,2010(5):5-9.
• [5]刘震雄,胡博.离心压缩机蜗壳内部流动特性的数值研究[J].机械研究与应用,2014(2):20-23.
• [6]李廷宾,闻苏平,汪志远,等.单级跨音速离心压缩机叶片扩压器和不同蜗壳形式耦合的内部流动数值研究[J].流体机械,2009,37(7):13-17.
• [7]冀春俊,王宇.离心压缩机末级扩压器与排气蜗壳集成优化[J].风机技术,2009(6):3-6.
• [8]张鹏飞,杜崇洋,金鑫.大型空分装置用离心式压缩机蜗壳的设计[J].通用机械,2015(12):50-53.
• [9]慈蕾,谢蓉,孙涛,等.离心式压缩机蜗壳优化设计[J].燃气轮机技术,2005,18(3):40-43.
• [10]Braembussche R A V D,Ayder E,Hagelstein D,et al.Improved Model for the Design and Analysis of Centrifugal Compressor Volutes[J].Journal of Turbomachinery,1999,121(3):619-625.11]陈沙古,卞如冈,黄进浩,等.深海高压压力筒抗剪环式密封结构受力分析[J].压力容器,2016,33(5):15-19.
• [12]范俊明,周启雄.气瓶热旋压成型的数值模拟[J].压力容器,2016,33(5):39-45.
• [13]万福腾,陈志平,焦鹏,等.含初始几何缺陷薄壁圆柱壳曲荷载的数值模拟方法研究[J].压力容器,2017,34(3):1-9.
• [14]陈明亚,王荣山,余炜炜,等.LBB弹塑性断裂分析中临界裂纹尺寸计算[J].压力容器,2016,33(1):40-45.
• [15]齐兆涛.涉外石油工程项目消防水喷淋设计安装要点[J].工业用水与废水,2017,48(2):77-79.
• [16]郑飞逸,何大江,陈锋,等.驱动合成气压缩机用工业汽轮机设计[J].机电工程,2016,33(10):1213-1216.
• [17]袁伟,赵杰,李峰,等.压缩机管线震动机理及减振技术研究综述[J].化工设备与管道,2016,53(2):36-42.
• [18]孙冠珂,李文,张雪辉,等.向心涡轮进气结构的气动性能及损失机理[J].航空动力学报,2015,30(8):1926-1935.