基于ANSYS的六缸压缩机曲轴模态分析及谐响应分析Modal and Harmonic Response Analysis of Crankshaft of a Six Cylinders Compressor by ANSYS
刘昌领,陈建义,李清平,仇晨,罗晓兰
LIU Chang-ling1,CHEN Jian-yi2,LI Qing-ping3,QIU Chen4,LUO Xiao-lan1(1.China University of Petroleum(Beijing)
摘要(Abstract)：
曲轴是压缩机的重要零部件之一,扭振破坏是六列以上的压缩机的主要失效形式。扭振破坏的主要影响因素是曲轴的模态。为此,本文针对某六缸压缩机曲轴,通过建立曲轴的振动学方程,利用ANSYS有限元计算方法,对某六缸压缩机曲轴进行八阶模态分析,分析结果表明可通过采取渗氮、滚压处理或加大曲轴过渡圆角半径等措施,达到减小曲轴变形和扭振的目的。另外,通过对曲轴的谐响应分析,计算出曲轴发生共振的频率、共振幅值和共振幅度最大的方位,为曲轴的进一步优化设计提供理论依据。
A crankshaft is one of the most important parts in compressors.The main destruction form of those that having six or more than six cylinders is torsion vibration.For this purpose,the paper took the crankshaft of the compressor that having six cylinders as an example.By establishing the vibration equations and using finite element method,the first 8 modal of the crankshaft was analysed,the conclusion shows that by taking the nitriding,rolling handling and increasing the fillet radius of the crankshaft,the purpose of reducing the deformation and torsional vibration of the crankshaft can be achieved.In addition,by the harmonic response analysis of it,the resonance frequencies and amplitudes of the crankshaft,and the position of the maximum resonance amplitude were calculated.They can provide a theoretical basis for the further design optimization of the crankshaft.
关键词(KeyWords)：
曲轴;扭振;模态分析;谐响应分析
crankshaft;torsion vibration;modal analysis;harmonic response analysis
基金项目(Foundation): 国家重大专项(2011ZX05026-004-01);; 国家高科技研究和发展计划(863项目:2012AA09A205)
作者(Author):
刘昌领,陈建义,李清平,仇晨,罗晓兰
LIU Chang-ling1,CHEN Jian-yi2,LI Qing-ping3,QIU Chen4,LUO Xiao-lan1(1.China University of Petroleum(Beijing)
参考文献(References)：
- [1]许增金,王世杰,李媛.往复压缩机轴系扭振有限元分析[J].机械强度,2011,33(1):137-142.
- [2]余永增,李锦龙,尹金明,等.2HA/2往复式压缩机气阀及磨损类故障分析与改进[J].流体机械,2011,39(7):62-66.
- [3]Friswell M I,Mottershead J E.Finite Element ModalUpdating in Structural Dynamics[J].Dordrecht,Klu-wer,1995.
- [4]Young Ju Bae,Jong-Bong Kim,et al.Mode change de-sign for capacity modulation in reciprocating compressor[J].Journal of Mechanical Science and Technology,2008,(22):1391-1399.
- [5]Otto K Riegger,Soedel W.Desien criteria and Perform-ance of an advanced reciprocating compressor[C].The1990 International compressor Technology Conferencesand Proceedings.West Lafayette:Purdue University,1990,11.
- [6]王利,向阳,卢艳辉,等.曲轴的建模及自由模态分析[J].洛阳工业高等专科学校学报,2004,14(1):8-10.
- [7]秦宇.ANSYS11.0基础与实例教程[M].北京:化学工业出版社,2009,1.
- [8]李连生,唐斌,王乐.往复压缩机曲轴变工况条件下有限元分析[J].流体机械,2011,39(12):14-17.
- [9]机械工程手册.机械振动[M].北京:机械工业出版社,1978,21.
- [10]邵景范,李文斌.基于ANSYS的电镀CBN砂轮模态及谐响应分析[J].机械工程与自动化,2011,4(2):67-69.
- [11]尚晓江,邱峰,赵海峰,等.ANSYS结构有限元高级分析方法与范例应用[M].北京:中国水利水电出版社,2008.
- [12]杨玉强,贺小华,杨建永.基于ANSYS的双管板换热器管板厚度设计探讨[J].压力容器,2010,27(10):34-39.
- [13]王宪,廖俊必.腐蚀管道的剩余强度评定及ANSYS二次开发[J].压力容器,2012,29(1):31-35.